Dustin A. Steed

**** **. **. 29-256-***-****

Piedmont, AL 36272 acg2uj@r.postjobfree.com

OBJECTIVE

Seeking a position as an Electrical Engineer Technician or Industrial Automation Technician in the electrical,

maintenance or manufacturing industry which would make use of my proven abilities in the electrical field and my

current education in Electrical Engineering Technology and Industrial Automation.

EDUCATION

Gadsden State Community College

• Electrical Engineering Technology GPA: 4.0 December 2014

• Industrial Automation aka Maintenance Degree GPA: 4.0 December 2014

Gadsden State Community College

• Welding Technology May 2005

EXPERIENCE

Moyer Electrical Gadsden, AL April 2013 – July 2014

Electrical Technician

• Installed underground and overhead 7200 volt primary services and components.

• Installed and updated CAT 5 and CAT 6 systems, security systems, fire alarms, heating and cooling

system controls, indoor and outdoor lighting and other common electrical components.

Anniston Army Depot Anniston, AL April 2006 March 2013

Quality Control / Heavy Mobile Equipment Mechanic

• Performed quality assurance tests using Human Interface Devices (HIDs), digital multimeters, infrared

data, calipers, oil analysis and other calibrated instruments to verify parts were functioning and within

tolerance.

Performed troubleshooting on defective motors, wiring harnesses, sensors, electronic, hydraulic

•

and pneumatic systems to understand, diagnose and repair the problem.

Drove vehicles on a closed test track to break in new parts properly and completed final

•

assessment reports, test records and other data sheets on their performances.

Used a wide variety of hand tools, power tools, test equipment and cranes up to 90 ton capacity.

•

Drove forklifts from 6,000 lb up to 65,000 lb capacity.

•

Used a tech manual to look up and order parts to ensure the job was completed in a timely

•

manner.

Bostrom Seating Piedmont, AL June 2003 April 2006

Welder

Used jigs and fixtures to assemble and weld pre stamped parts into various parts that had very

•

close tolerances.

Performed pre and post weld inspections on all parts to insure quality results.

•

Operated a plasma torch, MIG, TIG and stick welders and various other welding devices.

•

SKILLS

Installing and programming (PLC) Programmable Logic Controllers components and Allen

•

Bradley 500 programming

Programming and troubleshooting Fanuc 6 axis Robots

•

Troubleshooting faulty or defective instrumentation and control components

•

Troubleshooting complex electronic systems

•

Auto CADD Drafting and Chief Architect Design computer programming

•

Recalibrating precise instruments

•

Reading blueprints

•

Fluent with Microsoft Office computer applications

•

Certified welder in all positions with MIG, TIG and SMAW on steel and aluminum

•

Residential, Commercial and Industrial wiring

•

Operating forklifts from 6,000 Lb. up to 65,000 Lb. capacity

•

Operating heavy equipment [bulldozers, backhoes, excavators, large overhead cranes]

•

Certifications

• OSHA 10 safety certification

• NCCER (National Center for Construction Education and Research) safety certificate

• Certified Welder

• NTHS (National Technical Honors Society)

References

• Debbie Reynolds: Instructor 256-***-****

• Rudy Hamby: Supervisor at Anniston Army Depot 256-***-**** / 256-***-****

• Tim Odell: Supervisor at Anniston Army Depot 256-***-**** / 256-***-****

• Jonny Bullock: Supervisor at Anniston Army Depot 256-***-**** / 256-***-****

• Lowell Brothers: Instructor & former Southern Company Manager of Electrical & Controls

256-***-**** / 256-***-****

Contact this candidate