Roberto Perdomo

**** **** ******

San Diego, CA. 92154

ab99le@r.postjobfree.com

619-***-**** Mobile

OBJECTIVE

Field Service Engineer

Will utilize Technical Support skills and experience in Electromechanical Automated equipment and instrumentation in order to

install, set up, repair, and troubleshoot automated equipment and related instrumentation using common electrical and

mechanical tools.

SUMMARY

• Installation of Automated Equipment using schematics, diagrams and manuals, make mechanical and electrical Adjustments, repairs

& retrofit experience

• Electronics including Test Equipment such as DMM, Electrical and Hand tools, installation drawings, Electrical schematics and

mechanical drawings, Operation Manuals & service reports

• Road Warrior, Ability to travel 24/7

• 2 years Electronics Vocational Program

• Experience in Industrial Automated equipment, ability to wire and troubleshoot also perform mechanical retrofits

• Presently Attending Programmable Logic Controller Online Course PLCs (Programmable Logic Controllers Allen Bradley

• Ability to work alone or with limited supervision.

• Mechanical aptitude for this type of work

WORK EXPERIENCE

SOITEC San Diego, CA. 2012 – Present

Field Service Engineer Solar Power Plant

• Installation, maintenance and troubleshooting of Concentrated Photovoltaic Solar Trackers

• My job was to install signal, power wiring, TCU Control cabinet, wire motors, install transmission gears, load firmware, software, Limit

Switches, Encoders, VFD’s, PC Boards, contactors, relays and interface software to communicate to the power plant SCADA.

• I used mechanical hand tools and electrical meter to perform my job.

SIEMENS Dallas, Texas 2011 – 2012

Field Service Engineer Electromechanical

• Installation of automated mail sorting machines used by the United States Postal Service better known as AFCS 200 Automated Facer

Canceller System. I am contracted by VOLT to work for SIEMENS for the duration of project. I was part of a 4 men team that

assemble machine.

• My job was to install signal, power wiring, electrical control distribution units, wire motors, load software, and burn in in preparation for

testing, and assist on any task assigned by onsite supervisor.

• I used mechanical hand tools and electrical meter to perform my job. I also perform machine maintenance.

PAC Antek Instruments, Houston, Texas, 2008 2011

Field Service Engineer

• Provided Field Service Technical Support for Antek Sulfur Analyzers used in oil refinery process laboratories.

• Work with customers to answer technical questions regarding system hardware issues.

• Assist technicians in troubleshooting system failures over the phone and travel to site if required.

• Used mechanical hand tools and multi meter to help customer troubleshoot system.

• Our onsite services were bill to customers on per hour basis

International Dioxide. Kingstown, Rohde Island, 2006 2008

Field Service Engineer

• Provided Field Service technical support for Chlorine Dioxide Generators used for the drinking water purification process.

• Performed preventive maintenance

• Work with customers to resolve problems

• Follow up on system hardware issues. Assist technicians in troubleshooting system failures over the phone and travel to site if required.

Mechanical and tools and DMM.

SENSBEY INC. San Francisco, CA. 1996 2006

Field Service Engineer

• Provided technical support for customers over the phone, email or travel to site as required.

• Coordinated and Performed new machine installations, mechanical & electrical retrofits on wave solder machines, reflow ovens and spray

flux equipment used during the PCB board assembly process.

• Troubleshot machinery control circuits using multi meter and electrical schematics.

• Provided operation, maintenance and safety training to machine operators.

• Assisted SMT Electronic Manufacturing Process Engineers in setting up equipment for lead free soldering process. Evaluated process by

using developmental tools such as thermal profiles and impurity testers then made recommendations for the improvement of

automated soldering process.

• Installed new equipment for major brand consumer electronics manufacturing facilities throughout North & South America and Europe.

GONZALEZ & FARRAGO ENTERPRISES, El Monte, CA 1995 1996

Access Control & Gate Automation Technician

• Performed service calls and new installations.

• Automated gate & garage door installation for residential and commercial customers.

• Was responsible for the assigned service calls, company truck, equipment and tools.

LOCKHEED MARTIN AIRCRAFT, Ontario, CA 1993 1995

Aircraft Electrical Mechanic

• Fabricated electrical wire harness assembly and installation on C 130 military aircraft.

MCDONNELL DOUGLAS AIRCRAFT, Lakewood, CA 1984 1993

Aircraft Electrical Mechanic

• Fabricated electrical wire harness and installation on MD 11 commercial passenger aircraft.

EDUCATION

Mira Costa Community College, Oceanside, CA.

• Programmable Logic Controllers Technician Certificate. Presently enrolled in online course

Electronic Technician:

• Hacienda La Puente, Willow Campus, Los Angeles, Ca. 1993 1995 Electronics: AC, DC, Analog, Digital, Microprocessor, Multi meter,

Schematics, electronic control circuits.

ON THE JOB TRAINING

McDonnell Douglas; MD 11 Electrical Mechanic, 1984 – 1993

•

Lockheed Martin Aircraft; Electrical Installer USAF C 130E Aircraft, November 1993 1995

•

GONZALEZ & FARRAGO; Access Control & Gate Automation Technician 1995 1996

•

SENSBEY; Field Service Engineer, Automated reflow ovens and Wave Solder 1996 – 2006

•

International Dioxide; Field Service Engineer; • Provided Field Service technical support for Chlorine Dioxide Generators used for

•

the drinking water purification process. 2006 2008

PAC Antek Instruments, Field Service Engineer for Antek Sulfur Analyzers 2008 – 2011

•

SIEMENS; Field Service Technician; Installation of automated mail sorting machines 2011 – Present

•

SOITEC Solar commissioning, Operation and Maintenance on the job training

•

Contact this candidate